77 lines
2.2 KiB
Plaintext
77 lines
2.2 KiB
Plaintext
Small Form Factor (SFF) Committee Small Form-factor Pluggable (SFP)
|
|
Transceiver
|
|
|
|
Required properties:
|
|
|
|
- compatible : must be "sff,sfp"
|
|
|
|
Optional Properties:
|
|
|
|
- i2c-bus : phandle of an I2C bus controller for the SFP two wire serial
|
|
interface
|
|
|
|
- mod-def0-gpios : GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS)
|
|
module presence input gpio signal, active (module absent) high
|
|
|
|
- los-gpios : GPIO phandle and a specifier of the Receiver Loss of Signal
|
|
Indication input gpio signal, active (signal lost) high
|
|
|
|
- tx-fault-gpios : GPIO phandle and a specifier of the Module Transmitter
|
|
Fault input gpio signal, active (fault condition) high
|
|
|
|
- tx-disable-gpios : GPIO phandle and a specifier of the Transmitter Disable
|
|
output gpio signal, active (Tx disable) high
|
|
|
|
- rate-select0-gpios : GPIO phandle and a specifier of the Rx Signaling Rate
|
|
Select (AKA RS0) output gpio signal, low: low Rx rate, high: high Rx rate
|
|
|
|
- rate-select1-gpios : GPIO phandle and a specifier of the Tx Signaling Rate
|
|
Select (AKA RS1) output gpio signal (SFP+ only), low: low Tx rate, high:
|
|
high Tx rate
|
|
|
|
Example #1: Direct serdes to SFP connection
|
|
|
|
sfp_eth3: sfp-eth3 {
|
|
compatible = "sff,sfp";
|
|
i2c-bus = <&sfp_1g_i2c>;
|
|
los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>;
|
|
mod-def0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>;
|
|
tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>;
|
|
tx-fault-gpios = <&cpm_gpio2 19 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
&cps_emac3 {
|
|
phy-names = "comphy";
|
|
phys = <&cps_comphy5 0>;
|
|
sfp = <&sfp_eth3>;
|
|
};
|
|
|
|
Example #2: Serdes to PHY to SFP connection
|
|
|
|
sfp_eth0: sfp-eth0 {
|
|
compatible = "sff,sfp";
|
|
i2c-bus = <&sfpp0_i2c>;
|
|
los-gpios = <&cps_gpio1 28 GPIO_ACTIVE_HIGH>;
|
|
mod-def0-gpios = <&cps_gpio1 27 GPIO_ACTIVE_LOW>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&cps_sfpp0_pins>;
|
|
tx-disable-gpios = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>;
|
|
tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
p0_phy: ethernet-phy@0 {
|
|
compatible = "ethernet-phy-ieee802.3-c45";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&cpm_phy0_pins &cps_phy0_pins>;
|
|
reg = <0>;
|
|
interrupt = <&cpm_gpio2 18 IRQ_TYPE_EDGE_FALLING>;
|
|
sfp = <&sfp_eth0>;
|
|
};
|
|
|
|
&cpm_eth0 {
|
|
phy = <&p0_phy>;
|
|
phy-mode = "10gbase-kr";
|
|
};
|