510 lines
14 KiB
Plaintext
510 lines
14 KiB
Plaintext
Device Tree Clock bindings for arch-at91
|
|
|
|
This binding uses the common clock binding[1].
|
|
|
|
[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
|
|
|
|
Required properties:
|
|
- compatible : shall be one of the following:
|
|
"atmel,at91sam9x5-sckc" or
|
|
"atmel,sama5d4-sckc":
|
|
at91 SCKC (Slow Clock Controller)
|
|
This node contains the slow clock definitions.
|
|
|
|
"atmel,at91sam9x5-clk-slow-osc":
|
|
at91 slow oscillator
|
|
|
|
"atmel,at91sam9x5-clk-slow-rc-osc":
|
|
at91 internal slow RC oscillator
|
|
|
|
"atmel,at91rm9200-pmc" or
|
|
"atmel,at91sam9g45-pmc" or
|
|
"atmel,at91sam9n12-pmc" or
|
|
"atmel,at91sam9x5-pmc" or
|
|
"atmel,sama5d3-pmc":
|
|
at91 PMC (Power Management Controller)
|
|
All at91 specific clocks (clocks defined below) must be child
|
|
node of the PMC node.
|
|
|
|
"atmel,at91sam9x5-clk-slow" (under sckc node)
|
|
or
|
|
"atmel,at91sam9260-clk-slow" (under pmc node):
|
|
at91 slow clk
|
|
|
|
"atmel,at91rm9200-clk-main-osc"
|
|
"atmel,at91sam9x5-clk-main-rc-osc"
|
|
at91 main clk sources
|
|
|
|
"atmel,at91sam9x5-clk-main"
|
|
"atmel,at91rm9200-clk-main":
|
|
at91 main clock
|
|
|
|
"atmel,at91rm9200-clk-master" or
|
|
"atmel,at91sam9x5-clk-master":
|
|
at91 master clock
|
|
|
|
"atmel,at91sam9x5-clk-peripheral" or
|
|
"atmel,at91rm9200-clk-peripheral":
|
|
at91 peripheral clocks
|
|
|
|
"atmel,at91rm9200-clk-pll" or
|
|
"atmel,at91sam9g45-clk-pll" or
|
|
"atmel,at91sam9g20-clk-pllb" or
|
|
"atmel,sama5d3-clk-pll":
|
|
at91 pll clocks
|
|
|
|
"atmel,at91sam9x5-clk-plldiv":
|
|
at91 plla divisor
|
|
|
|
"atmel,at91rm9200-clk-programmable" or
|
|
"atmel,at91sam9g45-clk-programmable" or
|
|
"atmel,at91sam9x5-clk-programmable":
|
|
at91 programmable clocks
|
|
|
|
"atmel,at91sam9x5-clk-smd":
|
|
at91 SMD (Soft Modem) clock
|
|
|
|
"atmel,at91rm9200-clk-system":
|
|
at91 system clocks
|
|
|
|
"atmel,at91rm9200-clk-usb" or
|
|
"atmel,at91sam9x5-clk-usb" or
|
|
"atmel,at91sam9n12-clk-usb":
|
|
at91 usb clock
|
|
|
|
"atmel,at91sam9x5-clk-utmi":
|
|
at91 utmi clock
|
|
|
|
"atmel,sama5d4-clk-h32mx":
|
|
at91 h32mx clock
|
|
|
|
"atmel,sama5d2-clk-generated":
|
|
at91 generated clock
|
|
|
|
"atmel,sama5d2-clk-audio-pll-frac":
|
|
at91 audio fractional pll
|
|
|
|
"atmel,sama5d2-clk-audio-pll-pad":
|
|
at91 audio pll CLK_AUDIO output pin
|
|
|
|
"atmel,sama5d2-clk-audio-pll-pmc"
|
|
at91 audio pll output on AUDIOPLLCLK that feeds the PMC
|
|
and can be used by peripheral clock or generic clock
|
|
|
|
Required properties for SCKC node:
|
|
- reg : defines the IO memory reserved for the SCKC.
|
|
- #size-cells : shall be 0 (reg is used to encode clk id).
|
|
- #address-cells : shall be 1 (reg is used to encode clk id).
|
|
|
|
|
|
For example:
|
|
sckc: sckc@fffffe50 {
|
|
compatible = "atmel,sama5d3-pmc";
|
|
reg = <0xfffffe50 0x4>
|
|
#size-cells = <0>;
|
|
#address-cells = <1>;
|
|
|
|
/* put at91 slow clocks here */
|
|
};
|
|
|
|
|
|
Required properties for internal slow RC oscillator:
|
|
- #clock-cells : from common clock binding; shall be set to 0.
|
|
- clock-frequency : define the internal RC oscillator frequency.
|
|
|
|
Optional properties:
|
|
- clock-accuracy : define the internal RC oscillator accuracy.
|
|
|
|
For example:
|
|
slow_rc_osc: slow_rc_osc {
|
|
compatible = "atmel,at91sam9x5-clk-slow-rc-osc";
|
|
clock-frequency = <32768>;
|
|
clock-accuracy = <50000000>;
|
|
};
|
|
|
|
Required properties for slow oscillator:
|
|
- #clock-cells : from common clock binding; shall be set to 0.
|
|
- clocks : shall encode the main osc source clk sources (see atmel datasheet).
|
|
|
|
Optional properties:
|
|
- atmel,osc-bypass : boolean property. Set this when a clock signal is directly
|
|
provided on XIN.
|
|
|
|
For example:
|
|
slow_osc: slow_osc {
|
|
compatible = "atmel,at91rm9200-clk-slow-osc";
|
|
#clock-cells = <0>;
|
|
clocks = <&slow_xtal>;
|
|
};
|
|
|
|
Required properties for slow clock:
|
|
- #clock-cells : from common clock binding; shall be set to 0.
|
|
- clocks : shall encode the slow clk sources (see atmel datasheet).
|
|
|
|
For example:
|
|
clk32k: slck {
|
|
compatible = "atmel,at91sam9x5-clk-slow";
|
|
#clock-cells = <0>;
|
|
clocks = <&slow_rc_osc &slow_osc>;
|
|
};
|
|
|
|
Required properties for PMC node:
|
|
- reg : defines the IO memory reserved for the PMC.
|
|
- #size-cells : shall be 0 (reg is used to encode clk id).
|
|
- #address-cells : shall be 1 (reg is used to encode clk id).
|
|
- interrupts : shall be set to PMC interrupt line.
|
|
- interrupt-controller : tell that the PMC is an interrupt controller.
|
|
- #interrupt-cells : must be set to 1. The first cell encodes the interrupt id,
|
|
and reflect the bit position in the PMC_ER/DR/SR registers.
|
|
You can use the dt macros defined in dt-bindings/clock/at91.h.
|
|
0 (AT91_PMC_MOSCS) -> main oscillator ready
|
|
1 (AT91_PMC_LOCKA) -> PLL A ready
|
|
2 (AT91_PMC_LOCKB) -> PLL B ready
|
|
3 (AT91_PMC_MCKRDY) -> master clock ready
|
|
6 (AT91_PMC_LOCKU) -> UTMI PLL clock ready
|
|
8 .. 15 (AT91_PMC_PCKRDY(id)) -> programmable clock ready
|
|
16 (AT91_PMC_MOSCSELS) -> main oscillator selected
|
|
17 (AT91_PMC_MOSCRCS) -> RC main oscillator stabilized
|
|
18 (AT91_PMC_CFDEV) -> clock failure detected
|
|
|
|
For example:
|
|
pmc: pmc@fffffc00 {
|
|
compatible = "atmel,sama5d3-pmc";
|
|
interrupts = <1 4 7>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
#size-cells = <0>;
|
|
#address-cells = <1>;
|
|
|
|
/* put at91 clocks here */
|
|
};
|
|
|
|
Required properties for main clock internal RC oscillator:
|
|
- interrupt-parent : must reference the PMC node.
|
|
- interrupts : shall be set to "<0>".
|
|
- clock-frequency : define the internal RC oscillator frequency.
|
|
|
|
Optional properties:
|
|
- clock-accuracy : define the internal RC oscillator accuracy.
|
|
|
|
For example:
|
|
main_rc_osc: main_rc_osc {
|
|
compatible = "atmel,at91sam9x5-clk-main-rc-osc";
|
|
interrupt-parent = <&pmc>;
|
|
interrupts = <0>;
|
|
clock-frequency = <12000000>;
|
|
clock-accuracy = <50000000>;
|
|
};
|
|
|
|
Required properties for main clock oscillator:
|
|
- interrupt-parent : must reference the PMC node.
|
|
- interrupts : shall be set to "<0>".
|
|
- #clock-cells : from common clock binding; shall be set to 0.
|
|
- clocks : shall encode the main osc source clk sources (see atmel datasheet).
|
|
|
|
Optional properties:
|
|
- atmel,osc-bypass : boolean property. Specified if a clock signal is provided
|
|
on XIN.
|
|
|
|
clock signal is directly provided on XIN pin.
|
|
|
|
For example:
|
|
main_osc: main_osc {
|
|
compatible = "atmel,at91rm9200-clk-main-osc";
|
|
interrupt-parent = <&pmc>;
|
|
interrupts = <0>;
|
|
#clock-cells = <0>;
|
|
clocks = <&main_xtal>;
|
|
};
|
|
|
|
Required properties for main clock:
|
|
- interrupt-parent : must reference the PMC node.
|
|
- interrupts : shall be set to "<0>".
|
|
- #clock-cells : from common clock binding; shall be set to 0.
|
|
- clocks : shall encode the main clk sources (see atmel datasheet).
|
|
|
|
For example:
|
|
main: mainck {
|
|
compatible = "atmel,at91sam9x5-clk-main";
|
|
interrupt-parent = <&pmc>;
|
|
interrupts = <0>;
|
|
#clock-cells = <0>;
|
|
clocks = <&main_rc_osc &main_osc>;
|
|
};
|
|
|
|
Required properties for master clock:
|
|
- interrupt-parent : must reference the PMC node.
|
|
- interrupts : shall be set to "<3>".
|
|
- #clock-cells : from common clock binding; shall be set to 0.
|
|
- clocks : shall be the master clock sources (see atmel datasheet) phandles.
|
|
e.g. "<&ck32k>, <&main>, <&plla>, <&pllb>".
|
|
- atmel,clk-output-range : minimum and maximum clock frequency (two u32
|
|
fields).
|
|
e.g. output = <0 133000000>; <=> 0 to 133MHz.
|
|
- atmel,clk-divisors : master clock divisors table (four u32 fields).
|
|
0 <=> reserved value.
|
|
e.g. divisors = <1 2 4 6>;
|
|
- atmel,master-clk-have-div3-pres : some SoC use the reserved value 7 in the
|
|
PRES field as CLOCK_DIV3 (e.g sam9x5).
|
|
|
|
For example:
|
|
mck: mck {
|
|
compatible = "atmel,at91rm9200-clk-master";
|
|
interrupt-parent = <&pmc>;
|
|
interrupts = <3>;
|
|
#clock-cells = <0>;
|
|
atmel,clk-output-range = <0 133000000>;
|
|
atmel,clk-divisors = <1 2 4 0>;
|
|
};
|
|
|
|
Required properties for peripheral clocks:
|
|
- #size-cells : shall be 0 (reg is used to encode clk id).
|
|
- #address-cells : shall be 1 (reg is used to encode clk id).
|
|
- clocks : shall be the master clock phandle.
|
|
e.g. clocks = <&mck>;
|
|
- name: device tree node describing a specific peripheral clock.
|
|
* #clock-cells : from common clock binding; shall be set to 0.
|
|
* reg: peripheral id. See Atmel's datasheets to get a full
|
|
list of peripheral ids.
|
|
* atmel,clk-output-range : minimum and maximum clock frequency
|
|
(two u32 fields). Only valid on at91sam9x5-clk-peripheral
|
|
compatible IPs.
|
|
|
|
For example:
|
|
periph: periphck {
|
|
compatible = "atmel,at91sam9x5-clk-peripheral";
|
|
#size-cells = <0>;
|
|
#address-cells = <1>;
|
|
clocks = <&mck>;
|
|
|
|
ssc0_clk {
|
|
#clock-cells = <0>;
|
|
reg = <2>;
|
|
atmel,clk-output-range = <0 133000000>;
|
|
};
|
|
|
|
usart0_clk {
|
|
#clock-cells = <0>;
|
|
reg = <3>;
|
|
atmel,clk-output-range = <0 66000000>;
|
|
};
|
|
};
|
|
|
|
|
|
Required properties for pll clocks:
|
|
- interrupt-parent : must reference the PMC node.
|
|
- interrupts : shall be set to "<1>".
|
|
- #clock-cells : from common clock binding; shall be set to 0.
|
|
- clocks : shall be the main clock phandle.
|
|
- reg : pll id.
|
|
0 -> PLL A
|
|
1 -> PLL B
|
|
- atmel,clk-input-range : minimum and maximum source clock frequency (two u32
|
|
fields).
|
|
e.g. input = <1 32000000>; <=> 1 to 32MHz.
|
|
- #atmel,pll-clk-output-range-cells : number of cells reserved for pll output
|
|
range description. Sould be set to 2, 3
|
|
or 4.
|
|
* 1st and 2nd cells represent the frequency range (min-max).
|
|
* 3rd cell is optional and represents the OUT field value for the given
|
|
range.
|
|
* 4th cell is optional and represents the ICPLL field (PLLICPR
|
|
register)
|
|
- atmel,pll-clk-output-ranges : pll output frequency ranges + optional parameter
|
|
depending on #atmel,pll-output-range-cells
|
|
property value.
|
|
|
|
For example:
|
|
plla: pllack {
|
|
compatible = "atmel,at91sam9g45-clk-pll";
|
|
interrupt-parent = <&pmc>;
|
|
interrupts = <1>;
|
|
#clock-cells = <0>;
|
|
clocks = <&main>;
|
|
reg = <0>;
|
|
atmel,clk-input-range = <2000000 32000000>;
|
|
#atmel,pll-clk-output-range-cells = <4>;
|
|
atmel,pll-clk-output-ranges = <74500000 800000000 0 0
|
|
69500000 750000000 1 0
|
|
64500000 700000000 2 0
|
|
59500000 650000000 3 0
|
|
54500000 600000000 0 1
|
|
49500000 550000000 1 1
|
|
44500000 500000000 2 1
|
|
40000000 450000000 3 1>;
|
|
};
|
|
|
|
Required properties for plldiv clocks (plldiv = pll / 2):
|
|
- #clock-cells : from common clock binding; shall be set to 0.
|
|
- clocks : shall be the plla clock phandle.
|
|
|
|
The pll divisor is equal to 2 and cannot be changed.
|
|
|
|
For example:
|
|
plladiv: plladivck {
|
|
compatible = "atmel,at91sam9x5-clk-plldiv";
|
|
#clock-cells = <0>;
|
|
clocks = <&plla>;
|
|
};
|
|
|
|
Required properties for programmable clocks:
|
|
- interrupt-parent : must reference the PMC node.
|
|
- #size-cells : shall be 0 (reg is used to encode clk id).
|
|
- #address-cells : shall be 1 (reg is used to encode clk id).
|
|
- clocks : shall be the programmable clock source phandles.
|
|
e.g. clocks = <&clk32k>, <&main>, <&plla>, <&pllb>;
|
|
- name: device tree node describing a specific prog clock.
|
|
* #clock-cells : from common clock binding; shall be set to 0.
|
|
* reg : programmable clock id (register offset from PCKx
|
|
register).
|
|
* interrupts : shall be set to "<(8 + id)>".
|
|
|
|
For example:
|
|
prog: progck {
|
|
compatible = "atmel,at91sam9g45-clk-programmable";
|
|
#size-cells = <0>;
|
|
#address-cells = <1>;
|
|
interrupt-parent = <&pmc>;
|
|
clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>;
|
|
|
|
prog0 {
|
|
#clock-cells = <0>;
|
|
reg = <0>;
|
|
interrupts = <8>;
|
|
};
|
|
|
|
prog1 {
|
|
#clock-cells = <0>;
|
|
reg = <1>;
|
|
interrupts = <9>;
|
|
};
|
|
};
|
|
|
|
|
|
Required properties for smd clock:
|
|
- #clock-cells : from common clock binding; shall be set to 0.
|
|
- clocks : shall be the smd clock source phandles.
|
|
e.g. clocks = <&plladiv>, <&utmi>;
|
|
|
|
For example:
|
|
smd: smdck {
|
|
compatible = "atmel,at91sam9x5-clk-smd";
|
|
#clock-cells = <0>;
|
|
clocks = <&plladiv>, <&utmi>;
|
|
};
|
|
|
|
Required properties for system clocks:
|
|
- #size-cells : shall be 0 (reg is used to encode clk id).
|
|
- #address-cells : shall be 1 (reg is used to encode clk id).
|
|
- name: device tree node describing a specific system clock.
|
|
* #clock-cells : from common clock binding; shall be set to 0.
|
|
* reg: system clock id (bit position in SCER/SCDR/SCSR registers).
|
|
See Atmel's datasheet to get a full list of system clock ids.
|
|
|
|
For example:
|
|
system: systemck {
|
|
compatible = "atmel,at91rm9200-clk-system";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
ddrck {
|
|
#clock-cells = <0>;
|
|
reg = <2>;
|
|
clocks = <&mck>;
|
|
};
|
|
|
|
uhpck {
|
|
#clock-cells = <0>;
|
|
reg = <6>;
|
|
clocks = <&usb>;
|
|
};
|
|
|
|
udpck {
|
|
#clock-cells = <0>;
|
|
reg = <7>;
|
|
clocks = <&usb>;
|
|
};
|
|
};
|
|
|
|
|
|
Required properties for usb clock:
|
|
- #clock-cells : from common clock binding; shall be set to 0.
|
|
- clocks : shall be the smd clock source phandles.
|
|
e.g. clocks = <&pllb>;
|
|
- atmel,clk-divisors (only available for "atmel,at91rm9200-clk-usb"):
|
|
usb clock divisor table.
|
|
e.g. divisors = <1 2 4 0>;
|
|
|
|
For example:
|
|
usb: usbck {
|
|
compatible = "atmel,at91sam9x5-clk-usb";
|
|
#clock-cells = <0>;
|
|
clocks = <&plladiv>, <&utmi>;
|
|
};
|
|
|
|
usb: usbck {
|
|
compatible = "atmel,at91rm9200-clk-usb";
|
|
#clock-cells = <0>;
|
|
clocks = <&pllb>;
|
|
atmel,clk-divisors = <1 2 4 0>;
|
|
};
|
|
|
|
|
|
Required properties for utmi clock:
|
|
- interrupt-parent : must reference the PMC node.
|
|
- interrupts : shall be set to "<AT91_PMC_LOCKU IRQ_TYPE_LEVEL_HIGH>".
|
|
- #clock-cells : from common clock binding; shall be set to 0.
|
|
- clocks : shall be the main clock source phandle.
|
|
|
|
For example:
|
|
utmi: utmick {
|
|
compatible = "atmel,at91sam9x5-clk-utmi";
|
|
interrupt-parent = <&pmc>;
|
|
interrupts = <AT91_PMC_LOCKU IRQ_TYPE_LEVEL_HIGH>;
|
|
#clock-cells = <0>;
|
|
clocks = <&main>;
|
|
};
|
|
|
|
Required properties for 32 bits bus Matrix clock (h32mx clock):
|
|
- #clock-cells : from common clock binding; shall be set to 0.
|
|
- clocks : shall be the master clock source phandle.
|
|
|
|
For example:
|
|
h32ck: h32mxck {
|
|
#clock-cells = <0>;
|
|
compatible = "atmel,sama5d4-clk-h32mx";
|
|
clocks = <&mck>;
|
|
};
|
|
|
|
Required properties for generated clocks:
|
|
- #size-cells : shall be 0 (reg is used to encode clk id).
|
|
- #address-cells : shall be 1 (reg is used to encode clk id).
|
|
- clocks : shall be the generated clock source phandles.
|
|
e.g. clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>, <&audio_pll_pmc>;
|
|
- name: device tree node describing a specific generated clock.
|
|
* #clock-cells : from common clock binding; shall be set to 0.
|
|
* reg: peripheral id. See Atmel's datasheets to get a full
|
|
list of peripheral ids.
|
|
* atmel,clk-output-range : minimum and maximum clock frequency
|
|
(two u32 fields).
|
|
|
|
For example:
|
|
gck {
|
|
compatible = "atmel,sama5d2-clk-generated";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>, <&audio_pll_pmc>;
|
|
|
|
tcb0_gclk: tcb0_gclk {
|
|
#clock-cells = <0>;
|
|
reg = <35>;
|
|
atmel,clk-output-range = <0 83000000>;
|
|
};
|
|
|
|
pwm_gclk: pwm_gclk {
|
|
#clock-cells = <0>;
|
|
reg = <38>;
|
|
atmel,clk-output-range = <0 83000000>;
|
|
};
|
|
};
|