94 lines
3.2 KiB
Plaintext
94 lines
3.2 KiB
Plaintext
Texas Instruments sysc interconnect target module wrapper binding
|
|
|
|
Texas Instruments SoCs can have a generic interconnect target module
|
|
hardware for devices connected to various interconnects such as L3
|
|
interconnect (Arteris NoC) and L4 interconnect (Sonics s3220). The sysc
|
|
is mostly used for interaction between module and PRCM. It participates
|
|
in the OCP Disconnect Protocol but other than that is mostly independent
|
|
of the interconnect.
|
|
|
|
Each interconnect target module can have one or more devices connected to
|
|
it. There is a set of control registers for managing interconnect target
|
|
module clocks, idle modes and interconnect level resets for the module.
|
|
|
|
These control registers are sprinkled into the unused register address
|
|
space of the first child device IP block managed by the interconnect
|
|
target module and typically are named REVISION, SYSCONFIG and SYSSTATUS.
|
|
|
|
Required standard properties:
|
|
|
|
- compatible shall be one of the following generic types:
|
|
|
|
"ti,sysc-omap2"
|
|
"ti,sysc-omap4"
|
|
"ti,sysc-omap4-simple"
|
|
|
|
or one of the following derivative types for hardware
|
|
needing special workarounds:
|
|
|
|
"ti,sysc-omap3430-sr"
|
|
"ti,sysc-omap3630-sr"
|
|
"ti,sysc-omap4-sr"
|
|
"ti,sysc-omap3-sham"
|
|
"ti,sysc-omap-aes"
|
|
"ti,sysc-mcasp"
|
|
"ti,sysc-usb-host-fs"
|
|
|
|
- reg shall have register areas implemented for the interconnect
|
|
target module in question such as revision, sysc and syss
|
|
|
|
- reg-names shall contain the register names implemented for the
|
|
interconnect target module in question such as
|
|
"rev, "sysc", and "syss"
|
|
|
|
- ranges shall contain the interconnect target module IO range
|
|
available for one or more child device IP blocks managed
|
|
by the interconnect target module, the ranges may include
|
|
multiple ranges such as device L4 range for control and
|
|
parent L3 range for DMA access
|
|
|
|
Optional properties:
|
|
|
|
- clocks clock specifier for each name in the clock-names as
|
|
specified in the binding documentation for ti-clkctrl,
|
|
typically available for all interconnect targets on TI SoCs
|
|
based on omap4 except if it's read-only register in hwauto
|
|
mode as for example omap4 L4_CFG_CLKCTRL
|
|
|
|
- clock-names should contain at least "fck", and optionally also "ick"
|
|
depending on the SoC and the interconnect target module
|
|
|
|
- ti,hwmods optional TI interconnect module name to use legacy
|
|
hwmod platform data
|
|
|
|
|
|
Example: Single instance of MUSB controller on omap4 using interconnect ranges
|
|
using offsets from l4_cfg second segment (0x4a000000 + 0x80000 = 0x4a0ab000):
|
|
|
|
target-module@2b000 { /* 0x4a0ab000, ap 84 12.0 */
|
|
compatible = "ti,sysc-omap2";
|
|
ti,hwmods = "usb_otg_hs";
|
|
reg = <0x2b400 0x4>,
|
|
<0x2b404 0x4>,
|
|
<0x2b408 0x4>;
|
|
reg-names = "rev", "sysc", "syss";
|
|
clocks = <&l3_init_clkctrl OMAP4_USB_OTG_HS_CLKCTRL 0>;
|
|
clock-names = "fck";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
ranges = <0 0x2b000 0x1000>;
|
|
|
|
usb_otg_hs: otg@0 {
|
|
compatible = "ti,omap4-musb";
|
|
reg = <0x0 0x7ff>;
|
|
interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
|
|
<GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
|
|
usb-phy = <&usb2_phy>;
|
|
...
|
|
};
|
|
};
|
|
|
|
Note that other SoCs, such as am335x can have multipe child devices. On am335x
|
|
there are two MUSB instances, two USB PHY instances, and a single CPPI41 DMA
|
|
instance as children of a single interconnet target module.
|