207 lines
7.9 KiB
Plaintext
207 lines
7.9 KiB
Plaintext
|
4xx/Axon EMAC ethernet nodes
|
||
|
|
|
||
|
|
The EMAC ethernet controller in IBM and AMCC 4xx chips, and also
|
||
|
|
the Axon bridge. To operate this needs to interact with a this
|
||
|
|
special McMAL DMA controller, and sometimes an RGMII or ZMII
|
||
|
|
interface. In addition to the nodes and properties described
|
||
|
|
below, the node for the OPB bus on which the EMAC sits must have a
|
||
|
|
correct clock-frequency property.
|
||
|
|
|
||
|
|
i) The EMAC node itself
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- device_type : "network"
|
||
|
|
|
||
|
|
- compatible : compatible list, contains 2 entries, first is
|
||
|
|
"ibm,emac-CHIP" where CHIP is the host ASIC (440gx,
|
||
|
|
405gp, Axon) and second is either "ibm,emac" or
|
||
|
|
"ibm,emac4". For Axon, thus, we have: "ibm,emac-axon",
|
||
|
|
"ibm,emac4"
|
||
|
|
- interrupts : <interrupt mapping for EMAC IRQ and WOL IRQ>
|
||
|
|
- interrupt-parent : optional, if needed for interrupt mapping
|
||
|
|
- reg : <registers mapping>
|
||
|
|
- local-mac-address : 6 bytes, MAC address
|
||
|
|
- mal-device : phandle of the associated McMAL node
|
||
|
|
- mal-tx-channel : 1 cell, index of the tx channel on McMAL associated
|
||
|
|
with this EMAC
|
||
|
|
- mal-rx-channel : 1 cell, index of the rx channel on McMAL associated
|
||
|
|
with this EMAC
|
||
|
|
- cell-index : 1 cell, hardware index of the EMAC cell on a given
|
||
|
|
ASIC (typically 0x0 and 0x1 for EMAC0 and EMAC1 on
|
||
|
|
each Axon chip)
|
||
|
|
- max-frame-size : 1 cell, maximum frame size supported in bytes
|
||
|
|
- rx-fifo-size : 1 cell, Rx fifo size in bytes for 10 and 100 Mb/sec
|
||
|
|
operations.
|
||
|
|
For Axon, 2048
|
||
|
|
- tx-fifo-size : 1 cell, Tx fifo size in bytes for 10 and 100 Mb/sec
|
||
|
|
operations.
|
||
|
|
For Axon, 2048.
|
||
|
|
- fifo-entry-size : 1 cell, size of a fifo entry (used to calculate
|
||
|
|
thresholds).
|
||
|
|
For Axon, 0x00000010
|
||
|
|
- mal-burst-size : 1 cell, MAL burst size (used to calculate thresholds)
|
||
|
|
in bytes.
|
||
|
|
For Axon, 0x00000100 (I think ...)
|
||
|
|
- phy-mode : string, mode of operations of the PHY interface.
|
||
|
|
Supported values are: "mii", "rmii", "smii", "rgmii",
|
||
|
|
"tbi", "gmii", rtbi", "sgmii".
|
||
|
|
For Axon on CAB, it is "rgmii"
|
||
|
|
- mdio-device : 1 cell, required iff using shared MDIO registers
|
||
|
|
(440EP). phandle of the EMAC to use to drive the
|
||
|
|
MDIO lines for the PHY used by this EMAC.
|
||
|
|
- zmii-device : 1 cell, required iff connected to a ZMII. phandle of
|
||
|
|
the ZMII device node
|
||
|
|
- zmii-channel : 1 cell, required iff connected to a ZMII. Which ZMII
|
||
|
|
channel or 0xffffffff if ZMII is only used for MDIO.
|
||
|
|
- rgmii-device : 1 cell, required iff connected to an RGMII. phandle
|
||
|
|
of the RGMII device node.
|
||
|
|
For Axon: phandle of plb5/plb4/opb/rgmii
|
||
|
|
- rgmii-channel : 1 cell, required iff connected to an RGMII. Which
|
||
|
|
RGMII channel is used by this EMAC.
|
||
|
|
Fox Axon: present, whatever value is appropriate for each
|
||
|
|
EMAC, that is the content of the current (bogus) "phy-port"
|
||
|
|
property.
|
||
|
|
|
||
|
|
Optional properties:
|
||
|
|
- phy-address : 1 cell, optional, MDIO address of the PHY. If absent,
|
||
|
|
a search is performed.
|
||
|
|
- phy-map : 1 cell, optional, bitmap of addresses to probe the PHY
|
||
|
|
for, used if phy-address is absent. bit 0x00000001 is
|
||
|
|
MDIO address 0.
|
||
|
|
For Axon it can be absent, though my current driver
|
||
|
|
doesn't handle phy-address yet so for now, keep
|
||
|
|
0x00ffffff in it.
|
||
|
|
- phy-handle : Used to describe configurations where a external PHY
|
||
|
|
is used. Please refer to:
|
||
|
|
Documentation/devicetree/bindings/net/ethernet.txt
|
||
|
|
- rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec
|
||
|
|
operations (if absent the value is the same as
|
||
|
|
rx-fifo-size). For Axon, either absent or 2048.
|
||
|
|
- tx-fifo-size-gige : 1 cell, Tx fifo size in bytes for 1000 Mb/sec
|
||
|
|
operations (if absent the value is the same as
|
||
|
|
tx-fifo-size). For Axon, either absent or 2048.
|
||
|
|
- tah-device : 1 cell, optional. If connected to a TAH engine for
|
||
|
|
offload, phandle of the TAH device node.
|
||
|
|
- tah-channel : 1 cell, optional. If appropriate, channel used on the
|
||
|
|
TAH engine.
|
||
|
|
- fixed-link : Fixed-link subnode describing a link to a non-MDIO
|
||
|
|
managed entity. See
|
||
|
|
Documentation/devicetree/bindings/net/fixed-link.txt
|
||
|
|
for details.
|
||
|
|
- mdio subnode : When the EMAC has a phy connected to its local
|
||
|
|
mdio, which us supported by the kernel's network
|
||
|
|
PHY library in drivers/net/phy, there must be device
|
||
|
|
tree subnode with the following required properties:
|
||
|
|
- #address-cells: Must be <1>.
|
||
|
|
- #size-cells: Must be <0>.
|
||
|
|
|
||
|
|
For PHY definitions: Please refer to
|
||
|
|
Documentation/devicetree/bindings/net/phy.txt and
|
||
|
|
Documentation/devicetree/bindings/net/ethernet.txt
|
||
|
|
|
||
|
|
Examples:
|
||
|
|
|
||
|
|
EMAC0: ethernet@40000800 {
|
||
|
|
device_type = "network";
|
||
|
|
compatible = "ibm,emac-440gp", "ibm,emac";
|
||
|
|
interrupt-parent = <&UIC1>;
|
||
|
|
interrupts = <1c 4 1d 4>;
|
||
|
|
reg = <40000800 70>;
|
||
|
|
local-mac-address = [00 04 AC E3 1B 1E];
|
||
|
|
mal-device = <&MAL0>;
|
||
|
|
mal-tx-channel = <0 1>;
|
||
|
|
mal-rx-channel = <0>;
|
||
|
|
cell-index = <0>;
|
||
|
|
max-frame-size = <5dc>;
|
||
|
|
rx-fifo-size = <1000>;
|
||
|
|
tx-fifo-size = <800>;
|
||
|
|
phy-mode = "rmii";
|
||
|
|
phy-map = <00000001>;
|
||
|
|
zmii-device = <&ZMII0>;
|
||
|
|
zmii-channel = <0>;
|
||
|
|
};
|
||
|
|
|
||
|
|
EMAC1: ethernet@ef600c00 {
|
||
|
|
device_type = "network";
|
||
|
|
compatible = "ibm,emac-apm821xx", "ibm,emac4sync";
|
||
|
|
interrupt-parent = <&EMAC1>;
|
||
|
|
interrupts = <0 1>;
|
||
|
|
#interrupt-cells = <1>;
|
||
|
|
#address-cells = <0>;
|
||
|
|
#size-cells = <0>;
|
||
|
|
interrupt-map = <0 &UIC2 0x10 IRQ_TYPE_LEVEL_HIGH /* Status */
|
||
|
|
1 &UIC2 0x14 IRQ_TYPE_LEVEL_HIGH /* Wake */>;
|
||
|
|
reg = <0xef600c00 0x000000c4>;
|
||
|
|
local-mac-address = [000000000000]; /* Filled in by U-Boot */
|
||
|
|
mal-device = <&MAL0>;
|
||
|
|
mal-tx-channel = <0>;
|
||
|
|
mal-rx-channel = <0>;
|
||
|
|
cell-index = <0>;
|
||
|
|
max-frame-size = <9000>;
|
||
|
|
rx-fifo-size = <16384>;
|
||
|
|
tx-fifo-size = <2048>;
|
||
|
|
fifo-entry-size = <10>;
|
||
|
|
phy-mode = "rgmii";
|
||
|
|
phy-handle = <&phy0>;
|
||
|
|
phy-map = <0x00000000>;
|
||
|
|
rgmii-device = <&RGMII0>;
|
||
|
|
rgmii-channel = <0>;
|
||
|
|
tah-device = <&TAH0>;
|
||
|
|
tah-channel = <0>;
|
||
|
|
has-inverted-stacr-oc;
|
||
|
|
has-new-stacr-staopc;
|
||
|
|
|
||
|
|
mdio {
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <0>;
|
||
|
|
|
||
|
|
phy0: ethernet-phy@0 {
|
||
|
|
compatible = "ethernet-phy-ieee802.3-c22";
|
||
|
|
reg = <0>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
|
||
|
|
ii) McMAL node
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- device_type : "dma-controller"
|
||
|
|
- compatible : compatible list, containing 2 entries, first is
|
||
|
|
"ibm,mcmal-CHIP" where CHIP is the host ASIC (like
|
||
|
|
emac) and the second is either "ibm,mcmal" or
|
||
|
|
"ibm,mcmal2".
|
||
|
|
For Axon, "ibm,mcmal-axon","ibm,mcmal2"
|
||
|
|
- interrupts : <interrupt mapping for the MAL interrupts sources:
|
||
|
|
5 sources: tx_eob, rx_eob, serr, txde, rxde>.
|
||
|
|
For Axon: This is _different_ from the current
|
||
|
|
firmware. We use the "delayed" interrupts for txeob
|
||
|
|
and rxeob. Thus we end up with mapping those 5 MPIC
|
||
|
|
interrupts, all level positive sensitive: 10, 11, 32,
|
||
|
|
33, 34 (in decimal)
|
||
|
|
- dcr-reg : < DCR registers range >
|
||
|
|
- dcr-parent : if needed for dcr-reg
|
||
|
|
- num-tx-chans : 1 cell, number of Tx channels
|
||
|
|
- num-rx-chans : 1 cell, number of Rx channels
|
||
|
|
|
||
|
|
iii) ZMII node
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible : compatible list, containing 2 entries, first is
|
||
|
|
"ibm,zmii-CHIP" where CHIP is the host ASIC (like
|
||
|
|
EMAC) and the second is "ibm,zmii".
|
||
|
|
For Axon, there is no ZMII node.
|
||
|
|
- reg : <registers mapping>
|
||
|
|
|
||
|
|
iv) RGMII node
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible : compatible list, containing 2 entries, first is
|
||
|
|
"ibm,rgmii-CHIP" where CHIP is the host ASIC (like
|
||
|
|
EMAC) and the second is "ibm,rgmii".
|
||
|
|
For Axon, "ibm,rgmii-axon","ibm,rgmii"
|
||
|
|
- reg : <registers mapping>
|
||
|
|
- revision : as provided by the RGMII new version register if
|
||
|
|
available.
|
||
|
|
For Axon: 0x0000012a
|